Adachi, T., Y. Ohnishi and K. Arai. (1991) "Investigation of Toppling Slope Failure at Route 305 in Japan," in Proceedings, 7th International Congress on Rock Mechanics (Aachen, Germany, September 1991), pp. 843-846, W. Wittke, Ed. Rotterdam: Balkema.
Aglawe, J. P., and A. G. Corkum. (2006) "Application of Distinct Element Analysis in Slope Stability Problems," presented at the Indo-Norwegian Workshop on Seismic Hazard and Risk Assessment (New Delhi, India, March 2006).
Ahmadi, M., K. Goshtasbi and R. Ashjari. (2007) "Numerical Analyses of Masjed-E-Soleiman Powerhouse Cavern, Iran," in The Second Half Century of Rock Mechanics (11th Congress of the International Society for Rock Mechanics, Lisbon, July 2007), Vol. 2, pp. 951-954, L. Ribeiro e Sousa, C. Olalla, and N. Grossmann, Eds. London: Taylor & Francis Group.
Aikawa, A. (2011) "DEM Modeling Techniques for Dynamic Analysis of Ballasted Railway Track," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 10-01, pp. 587-596, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Albrecht, J. B. et al. (2010) "Application of Advanced Numerical Modelling Techniques for the Assessment of Cavability, Subsidence and Airblast Hazard in a Sublevel Cave Mine," in Caving 2010 (Proceedings, Second International Symposium on Block and Sublevel Caving, Perth, Australia, April 2010), pp. 495-508, Y. Potvin, Ed. Perth: Australian Centre for Geomechanics.
Alfonsi, P., J. L. Durville and X. Rachez. (1999) "Modelisation Numerique d'une Fondation sur Versant Rocheux par la Methode Des Elements Distincts: Comparaison 2-D/3-D," in Proceedings, 9th ISRM Congress on Rock Mechanics (Paris, France, 1999), Vol. 1, pp. 71-76. Rotterdam: Balkema.
Alkorta, A., M. Arlandi and A. Bernardo. (2010) "Design and Construction of a Large Cross-Section Cavern in Arraiz Tunnel of the Bilbao South Metropolitan By-Pass," in Tunnel Vision Towards 2020 (Proceedings, ITA - AITES 2010 World Tunneling Congress, Vancouver, May 2010). Paper No. fin00263.
Andrieux, P. P., R. K. Brummer and H. Li O'Connor. (2007) "Elastic Versus Inelastic Numerical Modelling of Deep and Highly Stressed Mining Fronts," in Deep Mining 07 (Fourth International Seminar on Deep and High Stress Mining, November 2007, Perth, Australia), pp. 51-57, Y. Potvin, Ed. Perth: Australian Centre for Geomechanics.
Andrieux, P. P. et al. (2008) "Calibration of Large-Scale Three-Dimensional Non-Linear Numerical Models of Underground Mines Using Microseismic Data," in Continuum and Distinct Element Numerical Modeling in Geo-Engineering (Proceedings, 1st International FLAC/DEM Symposium, Minneapolis, August 2008). Paper No. 07-04, R. Hart, C. Detournay, and P. Cundall, Eds. Minneapolis: Itasca Consulting Group, Inc.
Andrieux, P. P. et al. (2004) "Determination and Validation of the Rock Mass Post-Peak Mechanical Properties for a 3DEC Strain-Softening Model of the 680 Sill Pillar at Louvicourt Mine," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 121-127, H. Konietzky, Ed. Leiden: Balkema.
Andrieux, P. et al. (2000) "Large-Scale Panel Destress Blast at Brunswick Mine," in Proceedings, 23rd Study Session on Blasting Techniques (Society of Explosive Engineers of Quebec, Quebec City, November 2000), pp. 1-21.
Andrieux, P. et al. (2011) "Explicit Three-Dimensional Analysis of Structurally-Controlled Unraveling in Large Excavations," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 06-04, pp. 341-348, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Andrieux, P., R. Brummer and H. Zhu. (2003) Numerical Stress Analyses of Various Mining Sequences and Geomechanics Considerations at the Falconbridge Kidd #3 Mine - Phase II and Mine D, Itasca Consulting Canada Inc., Draft Report to Falconbridge Limited, Kidd Mining Division.
Antikainen, J., A. Simonen and I. Makinen. (1993) "3D Modelling of the Central Pillar in the Pyhasalmi Mine," in Innovative Mine Design for the 21st Century (International Congress on Mine Design, Kingston, Ontario, Canada, August 1993), pp. 631-640, W. F. Bawden and J. F. Archibald, Eds. Rotterdam: Balkema.
Applied Research Associates, I., and R. D. Hart et al. (1990) Tunnel Prediction Using Distinct Elements. Vol. II --- Computer Code Modification and Verification, Applied Research Associates, Inc., Itasca Consulting Group, Inc., Report to Defense Nuclear Agency, DNA-TR-90-56-V2, December. Alexandria, Virginia.
Asadizadeh, M., and R. Rahmannejad. (2010) "Numerical Modeling of Mechanical Behavior of a Jointed Rock Mass," in Proceedings, 44th U.S. Rock Mechanics Symposium (5th U.S.-Canada Rock Mechanics Symposium, Salt Lake City, Utah, June 2010). Paper No. 10-510. Alexandria, Virginia: ARMA.
Barton, N. (1997) "The Influence of Joint Properties in Modelling Jointed Rock Masses," in Proceedings, 8th International Congress on Rock Mechanics (Tokyo, September 1995), Vol. 3, pp. 1023-1032. Rotterdam: Balkema.
Bäckström, A. et al. (2009) "Analysis of Factors That Affect and Controls the Excavation Disturbance/Deformation Zone in Crystalline Rock," in SINOROCK 2009 --- Rock Characterisation, Modelling and Engineering Design Methods (CD Proceedings, ISRM-Sponsored International Symposium on Rock Mechanics,University of Hong Kong, May 2009).
Bigarre, P., K. B. Slimane and J. Tinucci. (1993) "3-Dimensional Modelling of Fault-Slip Rockbursting," in Rockbursts and Seismicity in Mines 93 (Kingston, Ontario, Canada, August 1993), pp. 315-319, R. P. Young, Ed. Rotterdam: Balkema.
Bigarre, P. et al. (1992) "3-Dimensional Modeling of Fault-Slip Rockbursting," Acta Montana (a), 2(88), 81-89.
Blair, S. C., S. R. Carlson and J. L. Wagoner. (2001) "Analysis of Geomechanical Behavior for the Drift Scale Test," in Proceedings, 9th International High-Level Radioactive Waste Management Conference (Las Vegas, April-May 2001). La Grange Park, Illinois: American Nuclear Society.
Blair, S. C., S. R. Carlson and J. L. Wagoner. (2001) "Distinct Element Modeling of the Drift Scale Test," in Rock Mechanics in the National Interest (38th U.S. Rock Mechanics Symposium, Washington, D.C., July 2001), Vol. 1, pp. 527-531. Rotterdam: Balkema.
Blair, S. C. et al. (2002) "Coupled THM Simulations of the Drift Scale Test at Yucca Mountain," in NARMS-TAC 2002: Mining and Tunnelling Innovation and Opportunity, Vol. 2, pp. 1383-1390, R. Hammah et al., Eds. Toronto: University of Toronto Press.
Board, M. (2000) "Numerical Examination of Mining-Induced Seismicity," in EUROCK '96 Special Lectures (ISRM International Symposium on Prediction and Performance in Rock Mechanics and Rock Engineering, Torino, Italy, September 1996), Vol. 3, pp. 1469-1486, G. Barla, Ed. Rotterdam: Balkema.
Board, M., R. Brummer and S. Seldon. (2001) "Use of Numerical Modeling for Mine Design and Evaluation," in Underground Mining Methods: Engineering Fundamentals and International Case Studies, pp. 483-491, W. A. Hustrulid and R. L. Bullock, Eds. Littleton, Colorado: SME.
Board, M. et al. (2000) "Analysis of the Failure of a Large Hangingwall Wedge: Kidd Mine Division, Falconbridge, Ltd," CIM Bull., 93(1043), 89-97 (September).
Board, M., and M. E. Pierce. (2009) "A Review of Recent Experience in Modeling of Caving," presented at the International Workshop on Numerical Modeling for Underground Mine Excavation Design, National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory, 43rd U.S. Rock Mechanics Symposium, Asheville, North Carolina, June 2009.
Botero, E. J., B. C. Mendez U. and M. P. Romo O. (2008) "Validation of Commercial Time Domain Finite Difference Codes for 3D Dynamic Soil-Structure Interaction Analysis," in Geomechanics in the Emerging Social & Technological Age (CD Proceedings, 12th IACMAG Conference, Goa, India, October 2008). Paper No. K47. Toronto: X-CD Technologies Inc.
Brideau, M.-A., and D. Stead. (2011) "The Influence of Three-Dimensional Kinematic Controls on Rock Slope Stability," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 04-05, pp. 213-220, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Brideau, M.-A. et al. (2009) "Preliminary Three-Dimensional Numerical Analyses of South Peak Area, Turtle Mountain, Alberta," in GeoHalifax 2009 (Proceedings, 62nd Canadian Geotechnical Conference / 10th Joint CGS/IAH-CNC Groundwater Conference, Halifax, Nova Scotia, September 2009)), pp. 382-389. Richmond, B.C., Canada: BiTech Publishers.
Brideau, M.-A., and D. Stead. (2009) "The Role of Rear Release Surfaces, Block Size and Lateral Confinement on Rock Slope Failure Mechanisms," in GeoHalifax 2009 (Proceedings, 62nd Canadian Geotechnical Conference / 10th Joint CGS/IAH-CNC Groundwater Conference, Halifax, Nova Scotia, September 2009)), pp. 489-496. Richmond, B.C., Canada: BiTech Publishers.
Brown, E. T. (2003) Block Caving Geomechanics (The International Caving Study I, 1997-2000). University of Queensland, JKMRC Monograph Series in Mining and Mineral Processing, Vol. 3. Indooroopilly, Australia: JKMRC.
Brummer, R. K., C. P. O'Connor and A. Turichshev. (2006) "Comprehensive Geomechanical Design of a Large Underground Observatory at 6800 Ft," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-1162, D. P. Yale et al., Eds. ARMA.
Brummer, R. K., H. Li and A. Moss. (2006) "The Transition from Open Pit to Underground Mining: An Unusual Slope Failure Mechanism at Palabora," in Stability of Rock Slopes in Open Pit Mining and Civil Engineering Situations (International Symposium, Cape Town, April 2006), pp. 411-420. SAIMM Symposium Series S44. Johannesburg: SAIMM.
Cappa, F. et al. (2006) "Hydromechanical Modelling of Pulse Tests That Measure Fluid Pressure and Fracture Normal Displacement at the Coaraze Laboratory Site, France," Int. J. Rock Mech. Min. Sci., 43, 1062-1082.
Carvalho, J. L., L. Castro and D. Elmo. (2010) "Geomechanical Numerical Modelling Work Flow for Large Open Pits Applied to Retro-Analysis of the East Wall of Toquepala Mine," in Proceedings, 44th U.S. Rock Mechanics Symposium (5th U.S.-Canada Rock Mechanics Symposium, Salt Lake City, Utah, June 2010). Paper No. ARMA 10-193. Alexandria, Virginia: ARMA.
Cavieres, P. et al. (2003) "Three-Dimensional Analysis of Fracturing Limits Induced by Large Scale Underground Mining at El Teniente Mine," in Soil and Rock America 2003 (39th U.S. Rock Mechanics Symposium, Cambridge, Massachusetts, June 2003), pp. 893-900, P. J. Culligan, H. H. Einstein, and A. J. Whittle, Eds. Essen: Verlag Glückauf.
Chen, S. G. et al. (2000) "3DEC Modeling of a Small-Scale Field Explosion Test," in Pacific Rocks 2000: Rock Around the Rim (4th North American Rock Mechanics Symposium, Seattle, July-August 2000), pp. 571-576, J. Girard et al., Ed. Rotterdam: Balkema.
Choi, S. O., J. D. Kim and K. S. Kim. (2007) "Enlarged Interpretation of Hydrofracturing in-Situ Stress by 3-D Numerical Analysis," in The Second Half Century of Rock Mechanics (11th Congress of the International Society for Rock Mechanics, Lisbon, July 2007), Vol. 2, pp. 865-868, L. Ribeiro e Sousa, C. Olalla, and N. Grossmann, Eds. London: Taylor & Francis Group.
Chong, W. L. et al. (2011) "3DEC Modeling of the Effect of Joints on Lateral Capacity of Socketed Pile in Laboratory Conditions," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 05-02, pp. 231-236, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Christianson, M., J. Itoh and S. Nakaya. (1995) "Seismic Analysis of the 25 Stone Buddhas Group at Hakone, Japan," in Rock Mechanics (35th U.S. Symposium, University of Nevada, Reno, June 1995), pp. 107-112, J. J. K. Daemen and R. A. Schultz, Eds. Rotterdam: Balkema.
Contador, N. V., and M. F. Glavic. (2001) "Sublevel Open Stoping at El Soldado Mine: A Geomechanic Challenge," in Underground Mining Methods: Engineering Fundamentals and International Case Studies, pp. 325-332, W. A. Hustrulid and R. L. Bullock, Eds. Littleton, Colorado: SME.
Corkum, A. G., and C. D. Martin. (2004) "Analysis of a Rock Slide Stabilized with a Toe-Berm: A Case Study in British Columbia, Canada," Int. J. Rock Mech. Min. Sci., 41, 1109-1121.
Cotesta, L. et al. (2007) "Application of Scientific Visualization --- Stress Control on Permeability Anisotropy in Moderately Fractured Rock," in Rock Mechanics: Meeting Society's Challenges and Demands (1st Canada-U.S. Rock Mechanics Symposium, Vancouver, May 2007), Vol. 2: Case Histories, pp. 1203-1212, E. Eberhardt et al., Ed. London: Taylor & Francis Group.
Coulthard, M. A., and I. H. Clark. (1991) "Computational Stress Analysis for Mine Excavation Design," in Computer Applications in the Mineral Industry (2nd Australian Conference, The University of Wollongong, July 1991), pp. 165-170, E. Y. Baafi, Ed. Wollongong: University of Wollongong.
Cundall, P. A. (1988) "Formulation of a Three-Dimensional Distinct Element Model - Part I: A Scheme to Detect and Represent Contacts in a System Composed of Many Polyhedral Blocks," Int. J. Rock Mech. Min. Sci. & Geomech. Abstr., 25, 107-116.
Cundall, P. A. (1994) "Alternative User Interfaces for Programs That Model Nonlinear Systems," in Applications of Computational Mechanics in Geotechnical Engineering, pp. 343-352, E. A. Vargas et al., Ed. Rotterdam: Balkema.
Cundall, P. A., and R. D. Hart. (1983) Development of Generalized 2-D and 3-D Distinct Element Programs for Modeling Jointed Rock, ICG Report, U.S. Army Engineering Waterways Experiment Station, published as Misc. Paper SL-85-1.
Cundall, P. A., and R. D. Hart. (1992) "Numerical Modeling of Discontinua," Engr. Comp., 9, 101-113; Comprehensive Rock Engineering, Vol. 2, pp. 231-243. J. A. Hudson, Ed. Oxford: Pergamon Press, 1993.
Cundall, P. A., M. E. Pierce and D. Mas Ivars. (2008) "Quantifying the Size Effect of Rock Mass Strength," in SHIRMS 2008 (Proceedings, 1st Southern Hemisphere International Rock Mechanics Symposium, Perth, Western Australia, September 2008), Vol. 2, pp. 3-15, Y. Potvin et al., Eds. Nedlands, Western Australia: Australian Centre for Geomechanics.
Damjanac, B., and C. Fairhurst. (2000) "Ecoulement Tri-Dimensionnel d'Eau Sous Pression dans les Milieux Fracturés," in La Sécurité Des Grands Ouvrages, Hommage Á Pierre Londe, pp. 5-19. Paris: Presses Pontes et Chauseés.
Damjanac, B., C. Fairhurst and T. Brandshaug. (1999) "Numerical Simulation of the Effects of Heating on the Permeability of a Jointed Rock Mass," in Proceedings, 9th ISRM Congress on Rock Mechanics (Paris, France, 1999), Vol. 2, pp. 881-885. Rotterdam: Balkema.
Damjanac, B. et al. (2010) "Liner Failure Around a Tunnel or a Storage Cell in Callovo-Oxfordian Clay," in Clays in Natural & Engineered Barriers for Radioactive Waste Confinement (4th International Meeting, March 2010): Abstracts, pp. 837-838. Nantes: ANDRA.
Dasgupta, B. (2000) "Numerical Modeling of Large Underground Caverns for Hydro Power Projects," in Trends in Rock Mechanics (Geo-Denver 2000, August 2000). Geotechnical Special Publication No. 102, pp. 50-64, J. F. Labuz, S. D. Glaser, and E. Dawson, Eds. Reston, Virginia: ASCE.
Dasgupta, B., and L. J. Lorig. (1995) "Numerical Modelling of Underground Power Houses in India," in Proceedings, International Workshop on Observational Method of Construction of Large Underground Caverns in Difficult Ground Conditions (8th ISRM International Congress on Rock Mechanics, Tokyo, September, 1995, Vol. 1, pp. 65-74, S. Sakurai, Ed.
Dasgupta, B., and L. J. Lorig. (1996) "Numerical Modelling of Underground Power Houses in India," J. Rock Mech. & Tunn. Tech., 2(2), 119-134 (July).
Dasgupta, B. et al. (1999) "Design of Underground Caverns for Tehri Hydropower Project, India by Numerical Modelling," in Proceedings, 9th ISRM Congress on Rock Mechanics (Paris, France, 1999), Vol. 1, pp. 357-358. Rotterdam: Balkema.
Dasgupta, B., and V. M. Sharma. (1999) "Numerical Modelling of Underground Power Houses in India," in Distinct Element Modeling in Geomechanics, pp. 187-217, V. M. Sharma et al., Ed. New Delhi: Oxford & IBH Publishing.
Decker, J. B. et al. (2006) "An Integrated Relational Database for Tracking Rock Mass Data During Tunnelling," in AITES-ITA 2006 (World Tunnel Congress & 32nd ITA General Assembly, Seoul, Korea, April 2006)I.-M. Lee, C. Yoo, and K.-H. You, Eds. Special issue of Tunn. Undergr. Sp. Tech., 21(3-4), Paper No. pita06-0312 (May-July). Elsevier Ltd.
Diederichs, M. S. et al. (2007) "Shear Strength Reduction (SSR) Approach for Slope Stability Analyses," in Rock Mechanics: Meeting Society's Challenges and Demands (1st Canada-U.S. Rock Mechanics Symposium, Vancouver, May 2007), Vol. 1: Fundamentals, New Technologies & New Ideas, pp. 319-327, E. Eberhardt et al., Ed. London: Taylor & Francis Group.
Dupin, J.-M., W. Sassi and J. Angelier. (1993) "Homogeneous Stress Hypothesis and Actual Fault Slip: A Distinct Element Analysis," J. Struct. Geol., 15(8), 1033-1043.
Esmaieli, K., J. Hadjigeorgiou and M. Grenon. (2010) "Estimating Geometrical and Mechanical REV Based on Synthetic Rock Mass Models at Brunswick Mine," Int. J. Rock Mech. Min., 47(6), 915-926.
Fairhurst, C. (1993) "Analysis and Design in Rock Mechanics: The General Context," in Comprehensive Rock Engineering, Vol. 2, pp. 1-29, J. A. Hudson, Ed. Oxford: Pergamon Press.
Fairhurst, C. (1995) "Three Gorges Dam Reservoir, Yangtze River, China," Felsbau, 13(6), 390-394.
Fairhurst, C. (1999) "Rock Mechanics and Nuclear Waste Repositories (Keynote Paper)," in Proceedings, International Workshop on the Rock Mechanics of Nuclear Waste Repositories (Vail, Colorado, June 1998), pp. 1-45, S. Saeb and C. Francke, Eds. Alexandria, Virginia: ARMA.
Fairhurst, C., B. Damjanac and R. Hart. (2000) "Numerical Analysis as a Practical Design Tool in Geo Engineering," in Slope Stability 2000 (Geo-Denver 2000, August 2000). Geotechnical Special Publication No. 101, pp. 169-183, D. V. Griffiths, G. A. Fenton, and T. R. Martin, Eds. Reston, Virginia: ASCE.
Fairhurst, C., and L. Lorig. (1999) "Improved Design in Rock and Soil Engineering with Numerical Modelling," in Distinct Element Modelling in Geomechanics, pp. 27-46, V. M. Sharma et al., Ed. New Delhi: Oxford & IBH Publishing.
Fairhurst, C. (2008) "Rock Mechanics and Conservation of Sites: Natural, Ancient and Modern," ISRM News. J., 11, 88-89.
Fekete, S., and Diederichs. (2010) "Tunnel Face Rockmass Characterization in Drill and Blast Tunnels Using LiDAR," in Tunnel Vision Towards 2020 (Proceedings, ITA - AITES 2010 World Tunneling Congress, Vancouver, May 2010). Paper No. fin00510.
Ferrero, A. M. et al. (2006) "Analysis of the Stability Condition of Underground Excavations by Experimental Measurements and 3D Numerical Modeling," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-1141, D. P. Yale et al., Eds. ARMA.
Gentier, S. et al. (2003) "Hydraulic Stimulation of Geothermal Wells in HFR Systems: Approach Based on 3D Hydro-Mechanical Modeling," in Soil and Rock America 2003 (39th U.S. Rock Mechanics Symposium, Cambridge, Massachusetts, June 2003), pp. 1471-1477, P. J. Culligan, H. H. Einstein, and A. J. Whittle, Eds. Essen: Verlag Glückauf.
Gentier, S. et al. (2005) "How to Understand the Effect of the Hydraulic Stimulation in Terms of Hydro-Mechanical Behavior at Soultz-Sous-Forêts (France)," GRC Trans., 29, 159-166.
Glamheden, R., Hökmark and R. Christiansson. (2004) "Modeling Creep in Jointed Rock Masses," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 131-137, H. Konietzky, Ed. Leiden: Balkema.
Grenon, M., and R. Caumartin. (2007) "Use of Resource Modeling Tools in Numerical Analysis of Slope Stability," in Rock Mechanics: Meeting Society's Challenges and Demands (1st Canada-U.S. Rock Mechanics Symposium, Vancouver, May 2007), Vol. 2: Case Histories, pp. 1295-1300, E. Eberhardt et al., Ed. London: Taylor & Francis Group.
Gutierrez, M. (2009) "Use of Remote Sensing Techniques and Distinct Element Modeling in the Study of a Massive Rockslide," in CD Proceedings, International Conference on Rock Joints and Jointed Rock Masses (Tucson, January 2009). Paper 1030, P. H. S. W. Kulatilake, Ed. Tucson: Kulatilake & Associates.
Hakami, H. (2006) "Numerical Study of the Shearing of Large Fractures Having Propagating Boundaries," in Rock Mechanics in Underground Construction (Proceedings, International Society for Rock Mechanics International Symposium 2006/4th Asian Rock Mechanics Symposium, Singapore, November 2006), p. 405, C. F. Leung and Y. X. Zhou, Eds. Singapore: World Scientific.
Hakami, H., and R. Christiansson. (2008) "A Numerical Study of the Stress Field at Forsmark Based on the Shearing Behaviour of Major Deformation Zones," in Geomechanics in the Emerging Social & Technological Age (CD Proceedings, 12th IACMAG Conference, Goa, India, October 2008). Paper No. I01. Toronto: X-CD Technologies Inc.
Hakami, H. (2007) "Propagation of Large, Twinned Fractures in Shear --- A Numerical Investigation," in The Second Half Century of Rock Mechanics (11th Congress of the International Society for Rock Mechanics, Lisbon, July 2007), Vol. 1, pp. 399-402, L. Ribeiro e Sousa, C. Olalla, and N. Grossmann, Eds. London: Taylor & Francis Group.
Hakami, H., and R. Christiansson. (2004) "Spatial Distribution of in-Situ Stresses at Äspö, Sweden --- 3DEC Analysis with Emphasis on the Role of Fracture Zones," in Contribution of Rock Mechanics to the New Century (Proceedings, International Society for Rock Mechanics 2004/3rd Asian Rock Mechanics Symposium, Kyoto, Japan, November - December 2004), Vol. 2, pp. 1283-1286, Y. Ohnishi and K. Aoki, Eds. Rotterdam: Mill Press.
Hammer, H., H. C. Siegfried Niedermeyer and T. Niedermeyer. (1995) "Untersuchen zu Gebrigs-Spannungen und -Bewegungen in der Schwabischen Alb," Felsbau, 13(6), 367-373.
Hart, R. (2003) "Enhancing Rock Stress Understanding Through Numerical Analysis," Int. J. Rock Mech. Min. Sci., 40, 1089-1097.
Hart, R. D. (1990) "Discontinuum Analysis for Deep Excavations in Jointed Rock," in Rock at Great Depth (ISRM/SPE International Symposium, Pau, France, August 1989), pp. 1123-1130, V. Maury and D. Fourmaintraux, Eds. Rotterdam: Balkema.
Hart, R. D. (1993) "An Introduction to Distinct Element Modeling for Rock Engineering," in Comprehensive Rock Engineering, Vol. 2, pp. 245-261, J. A. Hudson, Ed. Oxford: Pergamon Press.
Hart, R. D. et al. (1988) "Examination of Fault-Slip Induced Rockbursting at the Strathcona Mine," in Key Questions in Rock Mechanics, pp. 369-379, P. A. Cundall et al., Ed. Rotterdam: Balkema.
Hart, R. D., D. Hanson and D. Swan. (1990) "A Three-Dimensional Ground Control Program for Falconbridge Limited," in 92nd Annual General Meeting of CIM - May 1990. Ottawa: CIMM.
Hart, R., P. Cundall and J. Lemos. (1988) "Formulation of a Three-Dimensional Distinct Element Model - Part II: Mechanical Calculations for Motion and Interaction of a System Composed of Many Polyhedral Blocks," Int. J. Rock Mech., Min. Sci. & Geomech. Abstr., 25, 117-126.
Hart, R., and C. Fairhurst. (2000) "Application of Discontinuum Modeling in Geotechnical Studies for Nuclear Waste Isolation," in Geoecology and Computers (3rd International Conference on Advances of Computer Methods in Geotechnical and Geoenvironmental Engineering, Moscow, February 2000), pp. 15-28, S. A. Yufin, Ed. Rotterdam: Balkema.
Hellä, P., and P. Saksa. (1995) "3D Geological Modelling, Model Transfer and Validation," in Proceedings, SCSC'95 Conference (Ottawa, Canada, July 1995), pp. 967-971, T. I. Ören and L. G. Birta, Eds. SCS.
Herbst, M., H. Konietzky and K. Walter. (2008) "3D Microstructural Modeling," in Continuum and Distinct Element Numerical Modeling in Geo-Engineering (Proceedings, 1st International FLAC/DEM Symposium, Minneapolis, August 2008). Paper No. 08-05, R. Hart, C. Detournay, and P. Cundall, Eds. Minneapolis: Itasca Consulting Group, Inc.
Hosni, A. et al. (2004) "3D-Hydromechanical Modeling of Hydraulic Stimulation of Deep Geothermal Wells in Hot Fractured Rock at Soultz-Sous-Forêts (Alsace-France)," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 139-144, H. Konietzky, Ed. Leiden: Balkema.
Hökmark, H. (1996) "Acceptance of Emplacement Hole Positions - Stage 1 Thermomechanical Study," in Preprints, Workshop on Computational Methods in Engineering Geology (Lund, Sweden, October 1996), pp. 42-51, R. Pusch and R. Adey, Eds. Lund: Clay Technology.
Hökmark, H. (1996) "Numerical Study of the Performance of Tunnel Plugs," in Preprints, Workshop on Computational Methods in Engineering Geology (Lund, Sweden, October 1996), pp. 212-221, R. Pusch and R. Adey, Eds. Lund: Clay Technology.
Hudson, J. (1999) "Rock Mechanics Studies for Disposal of Radioactive Waste in the UK: 1979-1999," in Proceedings, International Workshop on the Rock Mechanics of Nuclear Waste Repositories (Vail, Colorado, June 1999), pp. 229-258, S. Saeb and C. Francke, Eds. Alexandria, Virginia: ARMA.
Hunt, S. P., B. A. Camac and P. J. Boult. (2006) "A New Geomechanical Tool for the Evaluation of Hydrocarbon Trap Integrity," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-1064, D. P. Yale et al., Eds. ARMA.
Hutchinson, D. J. et al. (2007) "Four Dimensional Considerations in Forensic and Predictive Simulation of Hazardous Slope Movement," in Rock Mechanics: Meeting Society's Challenges and Demands (1st Canada-U.S. Rock Mechanics Symposium, Vancouver, May 2007), Vol. 1: Fundamentals, New Technologies & New Ideas, pp. 11-19, E. Eberhardt et al., Ed. London: Taylor & Francis Group.
Itasca Consulting Group Inc. (2003) 3DEC (3-Dimensional Distinct Element Code), Version 3.0. Minneapolis: Minnesota.
Jakubowski, J. (2004) "3DEC Modeling Results Generalized by Stochastic Approach," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 165-173, H. Konietzky, Ed. Leiden: Balkema.
Jakubowski, J., and P. Starzec. (2002) "Deformable and Rigid Block Models Within the Scheme of Statistical Simulation," in NARMS-TAC 2002: Mining and Tunnelling Innovation and Opportunity, Vol. 2, pp. 1225-1232, R. Hammah et al., Eds. Toronto: University of Toronto Press.
Jakubowski, J., and J. B. Stypulokowski. (2006) "A Statistical Simulation of 3D Blocky Structure for Optimal Tunnel Design," in Geotechnical Engineering in the Information Technology Age (Geocongress 2006, Atlanta, February-March 2006), D. J. DeGroot et al., Eds. Reston, Virginia: ASCE. ISBN 0-7844-0803-3.
Jiang, Y. et al. (2010) "Numerical Evaluation of Cavern Layout Design for the Baihetan Hydropower Project in China," in Proceedings, 44th U.S. Rock Mechanics Symposium (5th U.S.-Canada Rock Mechanics Symposium, Salt Lake City, Utah, June 2010). Paper No. 10-119. Alexandria, Virginia: ARMA.
Jiao, Y. Y., J. Zhao and J. G. Cai. (2003) "Consideration for 2-D and 3-D Modelling of Shock Wave Propagation in Jointed Rock Masses," in Technology Roadmap for Rock Mechanics (10th Congress of the ISRM, Johannesburg, September 2003), Vol. 1, pp. 583-586. Johannesburg: SAIMM.
Jing, L. (2003) "A Review of Techniques, Advances and Outstanding Issues in Numerical Modelling for Rock Mechanics and Rock Engineering," Int. J. Rock Mech. Min. Sci., 40, 283-353.
Jing, L., and J. A. Hudson. (2002) "Numerical Methods in Rock Mechanics," Int. J. Rock Mech. Min. Sci., 39, 409-427.
Jing, L., E. Nordlund and O. Stephansson. (1994) "Technical Note: A 3-D Constitutive Model for Rock Joints with Anisotropic Friction and Stress Dependency in Shear Stiffness," Int. J. Rock Mech. Min. Sci. & Geomech. Abstr., 31(2), 173-178.
Jing, L., and O. Stephansson. (1987) Distinct Element Modelling of the Influence of Glaciation and Deglaciation of the State of Stress in Faulted Rock Masses, SKB, Report No. 88-23.
Jing, L., and O. Stephansson. (1989) "Numerical Modeling of Large-Scale Sublevel Stoping by Three-Dimensional Distinct Element Method," in Proceedings, 1st U.S. Conference on Distinct Elements (Golden, Colorado, October 1989). Golden, Colorado: CSM Press.
Jing, L., and O. Stephansson. (1990) Numerical Modeling of Sublevel Stoping for the Oscar Project Using a Three-Dimensional Distinct Element Code, Luleå University of Technology, Research Report TULEA 1990:19.
Jing, L., and O. Stephansson. (1991) "Distinct Element Modeling of Sublevel Stoping," in Proceedings, 7th International Congress on Rock Mechanics (Aachen, Germany, September 1991), Vol. 1, pp. 741-746. Rotterdam: Balkema.
Jing, L. (1990) Numerical Modelling of Jointed Rock Masses by Distinct Element Method for Two, and Three-Dimensional Problems. Doctoral Thesis, Luleå University of Technology, Division of Rock Mechanics, 1990:90, November.
Johansson, E. J. W. (1995) "Treating Sewage Underground," Tunnels & Tunnelling, 21-23 (July).
Johansson, E. J. W., and H. Kuula. (1995) "Three-Dimensional Back-Analysis Calculations of Viikinmäki Underground Sewage Treatment Plant in Helsinki," in Proceedings, 8th International Congress on Rock Mechanics (Tokyo, September 1995), Vol. II, pp. 597-600, T. Fujii, Ed. Rotterdam: Balkema.
Johansson, E. et al. (1991) "Comparisons of Computed Two- and Three-Dimensional Thermomechanical Response of Jointed Rock," in Proceedings, 7th International Congress on Rock Mechanics (Aachen, September 1991), pp. 115-119. Rotterdam: Balkema.
Johansson, E. et al. (1998) "Three-Dimensional Geomechanics Modelling: City Planning for the Kamppi Underground Bus Terminal in Helsinki," in Underground Construction in Modern Infrastructure, pp. 119-123, T. Franzon et al., Ed. Rotterdam: Balkema.
Johansson, E., J. Pöllä and P. Holopainen. (1996) "Predicted and Observed Behaviour of Weakness Zones in a Hard, Jointed Rock Mass," in Prediction and Performance in Rock Mechanics & Rock Engineering (EUROCK '96, Turin, September 1996), Vol. 1, pp. 271-276, G. Barla, Ed. Rotterdam: Balkema.
Johansson, E., and J. Rautakorpi. (2000) Rock Mechanics Stability at Olkiluoto, Hostholmen, Kivetty and Romuvaara, Posiva Oy, No. 2000-02.
Johansson, E., J. Rautakorpi and J. P. Tinucci. (2003) "Optimizing Tunnel Support Requirements in Jointed Rock - Applied to Wedge Stability Assessment of Waste Emplacement Drifts in Finland," in Soil and Rock America 2003 (39th U.S. Rock Mechanics Symposium, Cambridge, Massachusetts, June 2003), pp. 2341-2347, P. J. Culligan, H. H. Einstein, and A. J. Whittle, Eds. Essen: Verlag Glückauf.
Johansson, E. et al. (1999) "State-of-the-Art Nuclear Waste Repository Projects and Rock Mechanics in Finnish Program," in Proceedings, International Workshop on the Rock Mechanics of Nuclear Waste Repositories (Vail, Colorado, June 1998), pp. 117-141, S. Saeb and C. Francke, Eds. Alexandria, Virginia: ARMA.
Kalenchuk, K. S., S. D. McKinnon and M. S. Diederichs. (2007) "Dilution Source Prediction and Characterization for Blocky Rockmasses in Steep Walls or Cave Boundaries for Bulk Mining," in Proceedings, 1st International Symposium on Block and Sub-Level Caving (Cape Town, South Africa, October 2007), pp. 83-94. Johannesburg: SAIMM.
Kalenchuk, K. S., M. S. Diederichs and S. McKinnon. (2006) "Characterizing Block Geometry in Jointed Rockmasses," Int. J. Rock Mech. Min. Sci., 43, 1212-1225.
Kalenchuk, K. S., S. McKinnon and M. S. Diederichs. (2008) "Block Geometry and Rockmass Characterization for Prediction of Dilution Potential Into Sub-Level Cave Mine Voids," Int. J. Rock Mech. Min. Sci., 45, 929-940.
Kelly, M. S. et al. (1999) "Ground Behaviour About Longwall Faces and Its Effect on Mining," in Proceedings, 9th ISRM Congress on Rock Mechanics (Paris, France, 1999), Vol. 1, pp. 307-310. Rotterdam: Balkema.
Kim, B. H., P. K. Kaiser and G. Grasselli. (2007) Influence of Persistence on Behaviour of Fractured Rock Masses. Special issue of Geological Society, Special Publications, 284. London: The Geological Society.
Kim, B. H., F. T. Suorineni and P. K. Kaiser. (2008) "Approach to Estimate Rock Block Geometry for Determination of the Geological Strength Index (GSI)," in MASSMIN 2008 (5th International Conference on Mass Mining, Luleå, Sweden, June 2008), pp. 815-824, H. Schunnesson and E. Nordlund, Eds. Luleå: Division of Mining & Geotechnical Engineering, Luleå University of Technology.
Konietzky, H., P. Blümling and F. Rummel. (1995) "In Situ Stress Field in the Wellenberg Area," NAGRA Bull., 26, 38-48 (November).
Konietzky, H., P. Blümling and L. te Kamp. (1997) "Site Characterization: The Tectonic Stress Field for the Planned 'Wellenberg Repository Site' in Switzerland," in Preprints, GeoEngineering of Hazardous and Radioactive Waste Disposal (3rd European Geology Conference, University of Newcastle Upon Tyne, September 1997), pp. 275-285.
Konietzky, H., and P. Marschall. (1997) "Excavation Disturbed Zone Around Tunnels in Fractured Rock - Example from the Grimsel Test Site," in Geomechanics '96 (Roznov, Czech Republic, September 1997), pp. 235-240. Rotterdam: Balkema.
Konietzky, H., and L. te Kamp. (2004) "Numerical Stress Field Modeling for Underground Structures," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 155-164, H. Konietzky, Ed. Leiden: Balkema.
Konietzky, H., L. te Kamp and H. Hagedorn. (2004) "The Gotthard-Base-Tunnel: Conceptual Modeling for Tunneling Extremely Weak Zones," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 21-27, H. Konietzky, Ed. Leiden: Balkema.
Kulatilake, P. H. S. W. et al. (1992) "Use of the Distinct Element Method to Perform Stress Analysis in Rock with Non-Persistent Joints and to Study the Effect of Joint Geometry Parameters on the Strength and Deformability of Rock Masses," Rock Mech. Rock. Engng., 25(4), 253-274.
Kwon, S. et al. (2000) "Structural Stability Analysis for a High-Level Underground Nuclear Waste Repository in Granite," in Pacific Rocks 2000: Rock Around the Rim (4th North American Rock Mechanics Symposium, Seattle, July-August 2000), pp. 1279-1285, J. Girard et al., Ed. Rotterdam: Balkema.
Leach, A. R., and G. J. Van Hout. (1996) Modelling of Western Holdings 8 Shaft Pillar Extraction, Itasca Africa, Report PO18/96.
Lee, C.-I., S. Jeon and C. H. Lee. (2008) "Conservation of Stone Cultural Heritages in Korea," ISRM News. J., 11, 82-87.
Lemos, J. V. (1996) "Modelling of Arch Dams on Jointed Rock Foundations," in Prediction and Performance in Rock Mechanics & Rock Engineering (EUROCK '96, Turin, September 1996), Vol. 1, pp. 519-526, G. Barla, Ed. Rotterdam.
Lemos, J. V. (1998) "Discrete Analysis of the S. Vicente de Fora Model Test," in Monument 98 - Workshop on Seismic Performance of Monuments (Lisbon, November 1998), pp. 13-20. Lisbon: LNEC.
Lemos, J. V. (1998) "Discrete Element Modeling of the Seismic Behavior of Stone Masonry Arches," in Computer Methods in Structural Masonry 4 (4th International Symposium, Florence, Italy, September 1997), pp. 220-227, G. N. Pande et al., Ed. London: E&FN Spon.
Lemos, J. V. (1999) "Discrete Element Analysis of Dam Foundations," in Distinct Element Modeling in Geomechanics, pp. 89-115, V. M. Sharma et al., Ed. New Delhi: Oxford & IBH Publishing.
Lemos, J. V. (1999) "Numerical Models for Seismic Analysis of Historical Figures," in Proceedings, Assisi-99 Workshop on Seismic Performance of Built Heritage in Small Historical Centres (Assisi, April 1999), pp. K53-K51. CICOP Italia.
Lemos, J. V. et al. (1997) "Experimental Study of an Arch Dam on a Jointed Foundation," in Proceedings, 8th International Congress on Rock Mechanics (Tokyo, September 1995), Vol. 3, pp. 1263-1266. Rotterdam: Balkema.
Lemos, J. V. et al. (1998) "Three-Dimensional Analysis of a Block Masonry Pillar Using Discrete Elements," in Monument 98 - Workshop on Seismic Performance of Monuments (Lisbon, November 1998), pp. 117-126. Lisbon: LNEC.
Lendel, U. (2004) "Rock Bolting and Rock Support and Their Combination in Hard Coal Mining - A Comparative Study Made with UDEC," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 213-217, H. Konietzky, Ed. Leiden: Balkema.
Li, H., C. O'Connor and R. Brummer. (2008) 3DEC Numerical Modelling of Block Caving on the Stability of Key Infastructure at Oyu Tolgoi Mine, Itasca Consulting Canada Inc., Sudbury, Technical Memorandum, November 12.
Lightfoot, N. (1993) "The Use of Numerical Modeling in Rockburst Control," in Innovative Mine Design for the 21st Century (International Congress on Mine Design, Kingston, Ontario, Canada, August 1993), pp. 355-360, W. F. Bawden and J. F. Archibald, Eds. Rotterdam: Balkema.
Lin, M. et al. (2007) "Mechanical Degradation of Emplacement Drifts at Yucca Mountain --- A Modeling Case Study, Part I: Nonlithophysal Rock," Int. J. Rock Mech. Min. Sci., 44, 351-367.
Liu, C., and Y. Tan. (2004) "Use of 3DEC to Predict Roof Movements in Thick Coal Seam Operations Where Non-Entry Faces Are Employed," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 85-87, H. Konietzky, Ed. Leiden: Balkema.
Lorig, L. (1993) "The Roles and Necessary Capabilities of Numerical Methods for Design Analysis of Excavations in Rock," in Proceedings, VII National Congress on Soil Mechanics and Soil Engineering (Lima, December 1993), pp. 1-17. Lima: Servicomp Publicaciones.
Lorig, L. J. (1990) "Modeling of Support Structures in Hard Rock," in Kalliomekaniikan Paiva 1990 (Finnish Rock Mechanics Day 1990). Paper No. 9. Espoo, Finland: Vuorimiesyhdistys Bergsmannaforeningen.
Lorig, L. J. et al. (1989) "Influence of Discontinuity Orientations and Strength on Caveability in a Confined Environment," in Rock Mechanics as a Guide for Efficient Utilization of Natural Resources, pp. 167-174, A. W. Khair, Ed. Rotterdam: Balkema.
Lorig, L., and C. Fairhurst. (1992) "Three-Dimensional Discontinuum Modeling for Underground Excavations," in Proceedings, 1992 Rock Engineering Symposium (Taiwan, Tainan, Republic of China, December 1992), pp. 349-358., S.-T. Chen et al., Ed. Tainan, Taiwan: National Cheng Kung University.
Lorig, L. et al. (2010) "A Three-Dimensional Model for Rock Slopes Based on Micromechanics," in Proceedings, 44th U.S. Rock Mechanics Symposium (5th U.S.-Canada Rock Mechanics Symposium, Salt Lake City, Utah, June 2010). Paper No. 10-163. Alexandria, Virginia: ARMA.
Mas Ivars, D. (2006) "Water Inflow Into Excavations in Fractured Rock -- A Three-Dimensional Hydro-Mechanical Numerical Study," Int. J. Rock Mech. Min. Sci., 43, 705-725.
Mas Ivars, D., E. Hakami and O. Stephansson. (2004) "Influence of Rock Mass Characteristics on Inflow Into Deposition Holes for Nuclear Waste Disposal - A Coupled Hydro-Mechanical Analysis Using 3DEC," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 95-103, H. Konietzky, Ed. Leiden: Balkema.
McKellar, D. (2008) "Evaluating 3DEC as a Possible Code for the Characterization of Nuclear Reactor Internal Structures (Part I of II)," in Continuum and Distinct Element Numerical Modeling in Geo-Engineering (Proceedings, 1st International FLAC/DEM Symposium, Minneapolis, August 2008). Paper No. 03-04, R. Hart, C. Detournay, and P. Cundall, Eds. Minneapolis: Itasca Consulting Group, Inc.
McKinnon, S. D. (2001) "Analysis of Stress Measurements Using a Numerical Model Methodology," Int. J. Rock Mech. Min. Sci., 38, 699-709.
McKinnon, S. D., and L. J. Lorig. (1999) "Considerations for Three-Dimensional Modeling in Analysis of Underground Excavations," in Distinct Element Modelling in Geomechanics, pp. 145-166, V. M. Sharma et al., Ed. New Delhi: Oxford & IBH Publishing.
McKinnon, S. D., D. Harding and K. Birnie. (2002) "Crown Pillar Design at INCO's South Mine," in NARMS-TAC 2002: Mining and Tunnelling Innovation and Opportunity, Vol. 2, pp. 1041-1048, R. Hammah et al., Eds. Toronto: University of Toronto Press.
McLennan, J. et al. (2010) "Modeling Fluid Invasion and Hydraulic Fracture Propagation in a Naturally Fractured Rock, a Three Dimensional Approach," SPE Paper No. 127888, presented at the 2010 SPE International Symposium and Exhibition on Formation Damage Control, Lafayette, Louisiana, February 2010.
Meng, G. et al. (2010) "Interpretation of in-Situ Stress at Baihetan Project," in Proceedings, 44th U.S. Rock Mechanics Symposium (5th U.S.-Canada Rock Mechanics Symposium, Salt Lake City, Utah, June 2010). Paper No. 10-121. Alexandria, Virginia: ARMA.
Minkley, W. (2004) "Back Analysis Rock Burst Völkershausen 1989," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 105-112, H. Konietzky, Ed. Leiden: Balkema.
Minkley, W. et al. (2001) "A Visco-Elasto-Plastic Softening Model and Its Application for Solving Static and Dynamic Stability Problems in Potash Mining," in FLAC and Numerical Modeling in Geomechanics - 2001 (2nd International FLAC Conference, Lyon, France, October 2001), pp. 21-27, D. Billaux et al., Ed. Rotterdam: Balkema.
Mortazavi, A. et al. (2010) "Full-Scale 3D Slope Stability Analysis of Sarcheshmeh Mine West Wall," in Proceedings, 44th U.S. Rock Mechanics Symposium (5th U.S.-Canada Rock Mechanics Symposium, Salt Lake City, Utah, June 2010). Paper No. 10-486. Alexandria, Virginia: ARMA.
Nordlund, E., G. Radberg and L. Jing. (1992) "Determination of Failure Modes in Jointed Pillars by Numerical Modelling," in Proceedings, ISRM Regional Conference on Fractured and Jointed Rock Masses (Lake Tahoe, June 1992), Vol. 3, pp. 423-429. Berkeley, California: Lawrence Berkeley Laboratory.
Konietzky, H., Ed. (2004) Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004). Leiden: Balkema.
O'Connor, C. P. et al. (2004) "Numerical Modeling with 3DEC and Risk Assessment for a Geometrically Complex and Highly Stressed Sill Pillar at Onaping Mine," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 89-94, H. Konietzky, Ed. Leiden: Balkema.
Papantonopoulos, C. et al. (2002) "Numerical Prediction of the Earthquake Response of Classical Columns Using the Distinct Element Method," Earthquake Engng. Struct. Dyn., 31, 1699-1717.
Papastamatiou, D. et al. (1997) Monuments Under Seismic Action: A Numerical and Experimental Approach, National Technical University of Athens, Laboratory for Earthquake Engineering, Report to E.U. Environment Programme, NTUA/LEE-97-01.
Peng, Y.-R., and Y.-C. Chen. (2004) "The Deformation Behaviour of Tunnels Passing Through Rock Mass with Different Stiffness," in Rock Engineering: Theory and Practice (EUROCK 2004 & 53rd Geomechanics Colloquy, Salzburg, Austria, October 2004), pp. 765-770, W. Schubert, Ed. Essen: Verlag Glückauf.
Poisel, R., A. Preh and A. Zettler. (2004) "Rock as a Continuous Material and as a Discontinuous Material - Are Clear Definitions Possible?" in Rock Engineering: Theory and Practice (EUROCK 2004 & 53rd Geomechanics Colloquy, Salzburg, Austria, October 2004), pp. 717-722, W. Schubert, Ed. Essen: Verlag Glückauf.
Polson, A., and N. du Plooy. (2008) "Determining a Structure-Particle Interaction Using PFC3D (Part II of II)," in Continuum and Distinct Element Numerical Modeling in Geo-Engineering (Proceedings, 1st International FLAC/DEM Symposium, Minneapolis, August 2008). Paper No. 03-05, R. Hart, C. Detournay, and P. Cundall, Eds. Minneapolis: Itasca Consulting Group, Inc.
Psycharis, I. N. et al. (2003) "Numerical Study of the Seismic Behavior of a Part of the Parthenon Pronaos," Earthquake Engng. Struct. Dyn., 32, 2063-2084.
Ray, A. A. et al. (2006) "A Virtual Environment for Visualizing Fractures During Tunneling," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-1104, D. P. Yale et al., Eds. ARMA.
Reddy, M. N. et al. (2000) "Novel Approach to Optimise the Dimensions of Pillars in Underground Hard Rock Mine," in Geoecology and Computers (3rd International Conference on Advances of Computer Methods in Geotechnical and Geoenvironmental Engineering, Moscow, February 2000), pp. 451-459, S. A. Yufin, Ed. Rotterdam: Balkema.
Resende, R., J. V. Lemos and P. B. Dinis. (2004) "Application of a Discontinuity Model with Softening to the Analysis of Dam Foundations Using the Discrete Element Method," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 249-255, H. Konietzky, Ed. Leiden: Balkema.
Wyllie, D. C., and C. W. Mah, Eds. (2004) Rock Slope Engineering, 4th ed. London: Spon Press.
Rose, B. et al. (2011) "A Systematic Approach to Rock Mechanics Challenges at Xstrata Zinc Brunswick Mine," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 02-03, pp. 49-57, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Ryu, D.-W. et al. (2009) "Estimation of Key Block Size on a Large-Scale Rock Slope by 3-D Rock Joint System Simulation," in CD Proceedings, International Conference on Rock Joints and Jointed Rock Masses (Tucson, January 2009). Paper 1054, P. H. S. W. Kulatilake, Ed. Tucson: Kulatilake & Associates.
Sainsbury, D. P., and A. Grubb. (2011) "Investigation of Extreme Deformation at the N3500 Project," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 02-02, pp. 37-48, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Sainsbury, D. P., M. E. Pierce and L. J. Lorig. (2003) "Two- and Three-Dimensional Numerical Analysis of the Interaction Between Open-Pit Slope Stability and Remnant Underground Voids," in Harnessing Technology by Managing Data and Information (5th Large Open Pit Conference, Kalgoorlie, Western Australia, November 2003), pp. 251-257, C. Workman-Davies and E. Chanda, Eds. Carlton: AUSIMM.
Sainsbury, D. et al. (2007) "Three-Dimensional Discontinuum Analysis of Structurally Controlled Failure Mechanisms at the Cadia Hill Open Pit," in Slope Stability 2007 (Proceedings, 2007 International Symposium, Rock Slope Stability in Open Pit Mining and Civil Engineering, Perth, Australia, September 2007), pp. 307-320, Y. Potvin, Ed. Perth: Australian Centre for Geomechanics.
Salo, J.-P. et al. (1997) Further Developments of the Continuously-Yielding Joint Model for Studying Disposal of High-Level Nuclear Waste in Crystalline Rock (Yhteistyöprojekti II), Saanio & Riekkola Oy, Report T-2000-41/97.
Salzer, K., W. Minkley and T. Popp. (2004) "Safety Assessment for the Land Surface in the Vicinity of the Potash Shaft Neustassfurt VI," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 113-119, H. Konietzky, Ed. Leiden: Balkema.
Samadhiya, N. K., M. N. Viladkar and B. Singh. (2004) "Three-Dimensional Analysis of a Powerhouse Cavern in an Anisotropic Rock Mass"J. A. Hudson, and X.-T. Feng, Eds. Special issue of Int. J Rock Mech. Min. Sci, 41(3), Paper No. 2B 33 (April). Proceedings, ISRM SINOROCK2004 symposium (Three Gorges Project Site, China, May 2004).
Schelle, H., and G. Grünthal. (2004) "Synthetic Earthquake Sequences - Aspects of the Spatiotemporal Event Distribution," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 175-181, H. Konietzky, Ed. Leiden: Balkema.
Segalini, A. et al. (2006) "Stability Analysis of Fractured Rock Mass Excavation in Ornamental Stone Quarries by Mean of 3D Numerical Modelling," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-1088, D. P. Yale et al., Eds. ARMA.
Senís, M., and P. Varona. (2008) "3DEC Numerical Modeling of the Tindaya Mountain Project," in Continuum and Distinct Element Numerical Modeling in Geo-Engineering (Proceedings, 1st International FLAC/DEM Symposium, Minneapolis, August 2008). Paper No. 07-07, R. Hart, C. Detournay, and P. Cundall, Eds. Minneapolis: Itasca Consulting Group, Inc.
Severin, J., E. Eberhardt and K. S. Woo. (2010) "Influence of Major Fault Zones on 3D Ground Deformations Cause by Open Pit Block Cave Interactions," in Caving 2010 (Proceedings, Second International Symposium on Block and Sublevel Caving, Perth, Australia, April 2010), pp. 455-468, Y. Potvin, Ed. Perth: Australian Centre for Geomechanics.
Sharifzadeh, M., M. Ghorbani and R. Nateghi. (2007) "Long Term Stability Assessment of Siah Bisheh Pumped Storage Powerhouse Cavern Under Saturated Condition," in The Second Half Century of Rock Mechanics (11th Congress of the International Society for Rock Mechanics, Lisbon, July 2007), Vol. 2, pp. 947-950, L. Ribeiro e Sousa, C. Olalla, and N. Grossmann, Eds. London: Taylor & Francis Group.
Shen, B., and O. Stephansson. (1991) "Rock Mass Response to Glaciation and Thermal Loading from Nuclear Waste," in GEOVAL '90, pp. 550-558. Paris: Organization for Economic Co-Operation and Development.
Siebrits, E., M. W. Hildyard and A. Daehnke. (1994) "Elastodynamics: Past, Present and Future," in The Application of Numerical Modeling in Geotechnical Engineering, pp. 9-12. Pretoria: ISRM-SANG.
Simser, B. et al. (2002) "The Rock Mechanics Design for a 352 800 Tonne Mass Blast at the Brunswick Mine, Bathurst, New Brunswick," in NARMS-TAC 2002: Mining and Tunnelling Innovation and Opportunity, Vol. 1, pp. 815-823, R. Hammah et al., Eds. Toronto: University of Toronto Press.
Sjöberg, J. et al. (2011) "Forensic Analysis of a Rock Burst Event at the Kiirunavaara Mine --- Results and Implications for the Future," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 02-05, pp. 67-74, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Sjöberg, J., E. Nordlund and E. Olofsson. (1999) "Analysis of Rock Culverts Under Railroads," in Rock Mechanics for Industry (37th U.S. Rock Mechanics Symposium, Vail, Colorado, June 1999), Vol. 2, pp. 577-584, B. Amadei et al., Ed. Rotterdam: Balkema.
Staub, I., A. Fredriksson and R. Christiansson. (2003) "A Theoretical Model for the Characterisation of Rock Mass Mechanical Properties - Application at the Äspö HRL, Sweden," in Technology Roadmap for Rock Mechanics (10th Congress of the ISRM, Johannesburg, September 2003), Vol. 2, pp. 1161-1166. Johannesburg: SAIMM.
Stead, D. et al. (2006) "New Developments in Rock Slope Engineering: Implications for Open Pit Slope Design," in Sea to Sky Geotechnique (Canadian Geotechnical Conference & 7th Joint CGS/IAH-CNC Groundwater Specialty Conference, Vancouver, October 2006), pp. 1054-1061, Paper No. 0163-170.
Stephansson, O. (1999) "Rock Mechanics and Rock Engineering of Spent Nuclear Fuel and Radioactive Waste Repositories in Sweden," in Proceedings, International Workshop on the Rock Mechanics of Nuclear Waste Repositories (Vail, Colorado, June 1998), pp. 205-227, S. Saeb and C. Francke, Eds. Alexandria, Virginia: ARMA.
Stephansson, O., and B. Shen. (1991) "Modelling of Rock Masses for Site Location of a Nuclear Waste Repository," in Proceedings, 7th International Congress on Rock Mechanics (Aachen, Germany, September 1991), Vol. 1, pp. 157-162. Rotterdam: Balkema.
Stephansson, O., B. Shen and J. Lemos. (1991) "Modelling of Excavation, Thermal Loading and Bentonite Swelling Pressure for a Waste Repository," in High-Level Waste Management (2nd Annual International Conference, Las Vegas, Nevada, April-May 1991), pp. 1375-1381. New York: American Nuclear Society/ASCE.
Strouth, A., and E. Eberhardt. (2006) "The Use of LiDAR to Overcome Rock Slope Hazard Data Collection Challenges at Afternoon Creek, Washington," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-993, D. P. Yale et al., Eds. ARMA.
Taghavi, R., and M. Pierce. (2011) "Modeling Flow of Fragmented Rock with 3DEC: A Polyhedral DEM Approach," in Continuum and Distinct Element Modeling in Geomechanics --- 2011 (Proceedings, 2nd International FLAC/DEM Symposium (Melbourne, February 2011). Keynote Lecture, Paper 14-03, pp. 799-808, D. Sainsbury et al., Eds. Minneapolis: Itasca International Inc.
Thoraval, A. et al. (1995) "Coupled Thermo-Hydro-Mechanical Phenomena in Fractured Rocks: Recent Developments in Modelling Methods and Validation Tests (in French)," in Proceedings, 8th International Congress on Rock Mechanics (Tokyo, September 1995), Vol. 2, pp. 703-706, T. Fujii, Ed. Rotterdam: Balkema.
Tinucci, J. P. (1992) "A Ground Control Computer Program for Support Analyses of Three-Dimensional Critical Rock Blocks," in Rock Support in Mining and Underground Construction (International Symposium on Rock Support, Sudbury, Ontario, Canada, June 1992), pp. 49-56, P. K. Kaiser and D. R. McCreath, Eds. Rotterdam: Balkema.
Tinucci, J. P., and D. S. G. Hanson. (1990) "Assessment of Seismic Fault-Slip Potential at the Strathcona Mine," in Rock Mechanics Contributions and Challenges (31st U.S. Symposium on Rock Mechanics), pp. 753-760, W. A. Hustrulid and C. A. Johnson, Eds. Rotterdam: Balkema.
Tinucci, J. P., and J. Israelsson. (1991) Site Characterization and Validation - Excavation Stress Effects Around the Validation Drift, Stripa, Project Technical Report 91-20.
Tolppanen, P. J., E. J. W. Johansson and J. P. Salo. (1996) "Rock Mechanical Analyses of in-Situ Stress/Strength Ratio at the Posiva Oy Investigation Sites, Kivetty, Olkiluoto and Romuvaara, in Finland," in Prediction and Performance in Rock Mechanics & Rock Engineering (EUROCK '96, Turin, September 1996), Vol. 1, pp. 435-442, G. Barla, Ed. Rotterdam.
Tolppanen, P. J., E. Johansson and R. Riekkola. (1996) "Comparison of Vertical and Horizontal Deposition Hole Concept for Disposal of Spent Fuel Based on the Rock Mechanical in Situ Stress/Strength Analyses," in Preprints, Workshop on Computational Methods in Engineering Geology (Lund, Sweden, October 1996), pp. 230-237, R. Pusch and R. Adey, Eds. Lund: Clay Technology.
Tolppanen, P., E. Johansson and M. Hakala. (1995) Rock Mechanical Analyses of in Situ Stress/Strength Ratio at the TVO Investigation Sites Kivetty, Olkiluoto and Romuvaara, Nuclear Waste Commission of Finnish Power Companies, YJT-95-11.
Vakili, A., Y. J. Cai and B. Hebblewhite. (2008) "The Application of Itasca Codes for Cavability Assessment in Longwall Top Coal Caving Technology," in Continuum and Distinct Element Numerical Modeling in Geo-Engineering (Proceedings, 1st International FLAC/DEM Symposium, Minneapolis, August 2008). Paper No. 07-06, R. Hart, C. Detournay, and P. Cundall, Eds. Minneapolis: Itasca Consulting Group, Inc.
Vakili, A., and B. K. Hebblewhite. (2010) "A New Cavability Assessment Criterion for Longwall Top Coal Caving," Int. J. Rock Mech. Min. Sci., 47, 1317-1329.
Valdivia, C., and L. Lorig. (2000) "Slope Stability at Escondida Mine," in Slope Stability in Surface Mining, pp. 153-162, W. A. Hustrulid, M. K. McCarter, and D. J. A. Van Zyl, Eds. Littleton, Colorado: SME.
Venkatesh, H. S., and R. V. Rao. (2008) "Reduction of Blast Induced Ground Vibrations with Open Trenches in Surface Mines," in Geomechanics in the Emerging Social & Technological Age (CD Proceedings, 12th IACMAG Conference, Goa, India, October 2008). Paper No. O41. Toronto: X-CD Technologies Inc.
Voyat, I. et al. (2006) "Advanced Techniques for Geo Structural Surveys in Modelling Fractured Rock Masses: Application to Two Alpine Sites," in Golden Rocks 2006 --- 50 Years of Rock Mechanics, Colorado School of Mines (41st U.S. Rock Mechanics Symposium, June 2006). Paper No. 06-1138, D. P. Yale et al., Eds. ARMA.
Windsor, C. R. (1992) "Invited Lecture: Cable Bolting for Underground and Surface Excavations," in Rock Support in Mining and Underground Construction, pp. 349-366, P. K. Kaiser and D. R. McCreath, Eds. Rotterdam: Balkema.
Yan, M., D. Stead and M. Sturzenegger. (2007) "Step-Path Characterization in Rock Slopes: An Integrated Digital Imaging-Numerical Modeling Approach," in The Second Half Century of Rock Mechanics (11th Congress of the International Society for Rock Mechanics, Lisbon, July 2007), Vol. 1, pp. 693-696, L. Ribeiro e Sousa, C. Olalla, and N. Grossmann, Eds. London: Taylor & Francis Group.
Yong, S., P. K. Kaiser and S. Loew. (2010) "Influence of Tectonic Shears on Tunnel-Induced Fracturing," Int. J. Mech. Min., 47(6), 894-907.
Zhang, P. et al. (2008) "Determination and Verification of the Longitudinal Deformation Profile in a Horse-Shoe Shaped Tunnel Using Two-Stage Excavation," in MASSMIN 2008 (5th International Conference on Mass Mining, Luleå, Sweden, June 2008), pp. 845-854, H. Schunnesson and E. Nordlund, Eds. Luleå: Division of Mining & Geotechnical Engineering, Luleå University of Technology.
Zhu, F., O. Stephansson and Y. Wang. (1996) "Stability Investigation and Reinforcement for Slope at Daye Open Pit Mine, China," in Prediction and Performance in Rock Mechanics & Rock Engineering (EUROCK '96, Turin, September 1996), Vol. 1, pp. 621-625, G. Barla, Ed. Rotterdam: Balkema.
Zhu, H. (2004) "Discussion on the Determination of the Kbond Parameter for the Numerical Modeling of Cablebolt Elements with 3DEC," in Numerical Modeling of Discrete Materials in Geotechnical Engineering, Civil Engineering & Earth Sciences (1st International UDEC/3DEC Symposium, Bochum, Germany, September 2004), pp. 209-211, H. Konietzky, Ed. Leiden: Balkema.
Zhu, H., and Z. Zhou. (2009) "Displacement Analysis of the Left Abutment Slope of the Jinping I Dam," in Slope Stability 2009 (Universidad de Los Andes, Santiago, Chile, November 2009).
Zhu, H., H. Li and C. O'Connor. (2006) "Numerical Modeling of Brittle Rock Failure (in Chinese)," in Proceedings, 9th China National Rock Mechanics & Engineering Conference, pp. 260-266. Beijing: Science Publishing Co.
Last updated: 3/2/11
